DUAL CONTROL WAYS: The whip light can be controlled by the remote control or APP Bluetooth, 3000 colors, 300 changing modes, multiple brightness levels and flashing speeds for your choice, and can realize the display effects of chasing, flowing water, magic color, etc. Make you the center of attention and make you safer on the road.
STATUS INDICATOR LIGHT: Bevinsee LED whip lights can be used as signal lights, one wire controls two whip lights, and can simultaneously complete different indicator lights for the left turn, right turn, braking, and reversing, which is beautiful and safe.
DIY SPLICING DESIGN: One whip light has a total length of 120cm (4FT) and is assembled from a 60cm whip light with single base and a 60cm detachable whip light added section. You can install it in combination as you wish.
EASY INSTALLATION: Unique base wiring design, easier to route and disassemble. You just need to install the whip light in the 12.5mm hole, then connect the base wire and whip light, and finally power on. Done in less than 10 minutes. (Please refer to the installation instructions or installation video)
ROCK SOLID PERFORMANCE: These RGB LED whip lights are wrapped in EVA transparent heat shrink tube and high toughness silicone, which can be protected from sand, dust, rain, oxidation, waterproof, and shockproof, which improves the durability of this whip light and protects it from mechanical damage.
UNIVERSAL FITMENT: Bevinsee RGB whip lights are perfect for UTV ATV accessories, such as Polaris RZR, Can-Am Maverick, etc. See the below compatibility for details.
- Type: LED Whip
- Condition: Brand new
- Certification: CE, FCC, ROHS
- Color: RGB
- Length: 4FT (120cm)
- Voltage range: DC 9-15V
- LED Lifespan: 30,000 hours
- Placement on Vehicle: Front, Rear, Left, Right
- Control Way: App/Remote control
- Compatibility: ATV, UTV, off-road vehicles
- 2 x 4FT LED whip lights (2x 60cm with single base + 2x 60cm added section)
- 1 x Remote control (without battery)
- 1 x Installation Kit
1. The remote control battery is not provided. (battery type: 3V CR2025);
2. Before installation, check whether the hole size in the position to be installed is appropriate (the optimum hole size is 12.5 mm, it is recommended to use the professional whips light bracket);
3. The added section cannot be used alone;
4. After connection, the added section can't be in sync automatically in running light mode. You need to reset the APP.
5. After you complete the connection, you need to install the sealing rubber cover on the top of the whip light pole.
Bevinsee parts are not sponsored or endorsed by, or affiliated with the brands its parts fit, including Porsche, Subaru, Jaguar, BMW, Isuzu, Chrysler, Dodge, Jeep, Buick, Cadillac, Chevrolet, GMC, Volvo, Land Rover, Oldsmobile, Pontiac, Ford, Lincoln, Mercury, Acura, KIA, Nissan, Infiniti, International Harvester, Mitsubishi, Audi, Lexus, Toyota, Mazda, Volkswagen, Suzuki, Saab, Honda, Alfa Romeo, Saleen, Mercedes-Benz, Nash, Hummer, Freightliner, Datsun, Saturn, Turner, Geo, Lada, Fiat, Daihatsu, Opel, Vauxhall, Sabra, Tesla, Ram, Rover, Skoda, Healey, Mini, Smart, Scion, Renault, Seat, Peugeot, Merkur, Astra, Tucker, VW, Routan, Tiguan, Touareg, Jetta, Gti, Passat, Golf, Bosch, Denso, Holden, Chery, Mercedes Benz, Holden Special Vehicles, Hyundai, Trabant, Citroën, Freightline, Textron/Arctic Cat, CFMOTO ZForce etc.